The 32 Best Hdpe Filaments in 2023

1 KG (approximately 2.20 lbs) Spool

1.75mm Filament Diameter (Dimensional Accuracy +/- 0.03mm)

PLA (Polylactic Acid) 3D Printer Filament Vacuumed Sealed With Desiccant

Recommended Extrusion/Nozzle Temperature 180°C - 210°C (356°F - 410°F)

Spool Diameter: 7.88" - Spool Width: 2.69" - Spool Hub Hole Diameter: 2.20"

1 KG (approximately 2.20 lbs) Spool

1.75mm Filament Diameter (Dimensional Accuracy +/- 0.03mm)

PLA (Polylactic Acid) 3D Printer Filament Vacuumed Sealed With Desiccant

Recommended Extrusion/Nozzle Temperature 180°C - 220°C

Spool Diameter: 7.88" - Spool Width: 2.69" - Spool Hub Hole Diameter: 2.20"

Heat-resisting and durable, with high rigidity and flexibility

Low warping, easy to print with

Chemical-resistant, tolerant to a variety of chemicals and detergents

High dimensional accuracy of 1.75 mm (±0.03 mm) diameter

Wide applicability, compatible with most 3D printers

1 KG (approximately 2.20 lbs) Spool; Eco-Friendly, Odorless. Less Warping

1.75mm Filament Diameter (Dimensional Accuracy +/- 0.03mm)

PLA (Polylactic Acid) 3D Printer Filament Vacuumed Sealed With Desiccant

Recommended Extrusion/Nozzle Temperature 180°C - 210°C (356°F - 410°F)

Spool Diameter: 7.88" - Spool Width: 2.69" - Spool Hub Hole Diameter: 2.20"

Blending a mixture of plant-based materials and polymers creates HATCHBOX 3D Printer's PLA

①【Remove Excess Moisture】→3D printer filaments are hygroscopic, moisture can cause printing failure, SUNLU dry box can remove the excess moisture, keep the filament dry.

②【Fully assembled and easy to use】→It's simple to operate, turn on by hit either button, hold the left button to change the dry time, press the right button to change the temperature setting.

③【Simple but Effective】→The print quality will be better if using dried filament, surface smoother, layer adhesion increased. It can help if you live in a humid temperature zone.

④【High Compatibility】→The adjustable temperature(time) range is 35-55℃(0-24hours), the SUNLU dryer can bake 1KG any type of filament at a designated temperature for hours.

⑤【Dry During 3D Printing】→Dust-free, moisture-free. The filament dryer is a great addition to 3d printer, it can keep the filament dry during 3d printing, no more brittle PLA, PETG, ABS filament.

【Crealty Ender PLA】As the brand manufacturer of Crealty 3D printers, Ender brings more professional 1.75mm PLA 3D printer filament. The Imported raw material upgrades with stronger toughness. It is not easy to break, offering clog-free, bubble-free, and tangle-free printing.

【High Consistency and Smooth Output】The Ender PLA printer filament is controlled 1.75mm within ±0.03mm. So that the feeding is smoother and the material is not easily broken to ensure continuous printing. Recommended Extrusion/Nozzle Temperature 195°C - 220°C, Bed 55°C - 60°C for better printing results.

【Made of Corn Starch Materials】Non-toxic, No irritating smell and can be naturally degraded safer for children or students operating. Suitable for use in schools, homes, and offices.Whether for entertainment or work, Ender PLA 3D printing filament can give you a better experience.

【Wide compatibility】Due to the high-quality manufacturing accuracy standards and the small diameter tolerance of +/- 0.03mm, it can be perfectly compatible with all common 1.75mm 3D printers. Smoother fluidity makes the printing easier without plugging, which realizes the exquisite results. The upgrade raw material makes the model support easier to add and remove without warping.

【Easy to Use, Clog-Free, Bubble-Free】Good vacuum packing ensures the filament is dry, easy to store, and use. Ender PLA 3D printing filament adopts a new design, which promises that you will be very smooth during use. Choose Ender PLA 3D Printing filament, you will get a better printing experience.

【Function - Dryer and Storage Box】SUNLU dry box is specifically made for the purpose of drying 3d printer filament, intended to remove moisture from a spool of filament. It can keep 3D filament dried during a print job and can be used to dry filament for storage.

【Heating, Rotating and Constant Temperature】The storages box will keep heating up to your preset temperature, and keep working until up to the preset time. SUNLU Enclosure box has two built-in rotating shafts that allow the filament to continuously rotate in a dry hot box to remove moisture.

【Simple Yet Effective】The filament dryer box is pretty easy to use, it crams in a lot of functionality even with only two buttons, such as set temperature and time, load the data of the current temperature and the current target temperature.

【Set Temperature and Time】The dryer box is preset to run for 6 hours at 50℃ which should be compatible with pretty much any material any diameter of the filament. but you could click the buttons to reset the temperature between 35-55℃, or long-press the left button to reset the working time between 0-24 hours.

【Quiet and Good Looking】The SUNLU filament dryer storage enclosure is very silent when it working, it can be used in your bedroom with your silence 3d printer and won't be noisy to disturb you. It's designed with a transparent lid and a white bottom, which is simple and beautiful.

1KG net (approximately 2.2 lbs) PLA Filament with Clear Spool or Black Spool

eSUN PLA PRO 3D Printer Filament Vacuumed Sealed With Desiccant. Superb layer bonding. Several times stronger than PLA.

1.75mm Filament Diameter (Dimensional Accuracy +/- 0.05mm)

Recommended Extrusion/Nozzle Temperature 205C - 225C

Spool Diameter: 8" - Spool Width: 2.50" - Spool Hub Hole Diameter: 2.05" - Inner Circle Diameter: 3.5"

【Mechanical Properties】-- Tensile strength (X-Y): 31.9 ± 1.1 (MPa), Elongation at break (X-Y): 6.8 ± 0.9 (%), Bending modulus: 1174 ± 64 (MPa), Bending strength: 53.7 ± 2.4 (MPa), Charpy impact strength: 5.1 ± 0.3 (kJ/m2).

【Clog-free & Bubble-Free】-- Designed and Manufactured with Clog-Free patent to guarantee a smooth and stable printing experience. Complete drying for 24 hours before vacuum aluminum foil packaging, which can effectively protect the PETG filament from moisture. As the PETG material is sensitive to moisture, please remember to put it back into the re-sealable aluminum foil bag timely after using to maintain excellent printing result

【Less- tangle and Easy to Use】-- Full mechanical winding and strict manual examination, which guarantee the PETG filaments tidy and easy to be fed; Larger spool inner diameter design makes feeding smoother

【Dimensional Accuracy & Consistency】 -- Advanced CCD diameter measuring and self-adaptive control system in the manufacturing guarantee these PLA filaments of 1.75 mm diameter, dimensional accuracy + / - .05 mm; 1 kg spool (2.2lbs)

【Cost-effective and Wide Compatibility】 -- With over 8 years’ 3D filaments R & D experience, thousands tons of filaments output every month, Overture is capable of manufacturing all kinds of filaments in large scale with premium quality, which contribute to Overture filament cost-effective and reliable for most common 3D printers, such as MK3, Ender 3, Monoprice FlashForge and more

Material: PLA(Polylactic Acid) - Weight: 1 KG (approximately 2.20 lbs) Spool

Size: 1.75mm (Tolerance Level : ± 0.03mm) - Spool Diameter: 7.87" - Spool Width: 2.83" - Spool Hub Hole Diameter: 2.20"

Recommended Printing Temp: 195-220°C - Base Plate Temp: 20-50°C

Performance Advantages: The strength and toughness of our PRILINE PLA filament is higher than the general PLA filament on the market.